Petroleum Containment
Icon Containment Solutions
Narrow Your Results
Mfr / Trade Name
Category - Main
Dispenser Replacement Parts
Containment Sumps, Monitoring Wells & Flex Connectors
Fiberglass
Accessory
Type
Composition
Size
Voltage
- List View
- Gallery View
| Page of 2 |
1 Gallon Epoxy Bonding Kit
Item No. E154CM
Gel Time 10 minutes at 65 Degrees F 10 minutes at 95 Degrees F Cure Time 2 Hours at 65 Degrees F 45 Minutes at 95 Degrees F
Fueling System Emergency Shut-Down E-Stop Switch With Surface-Mount Weatherproof Enclosure And Clear Hinged Spring-Loaded Cover
Item No. EM01
Fueling system emergency shutdown switch mounted in a weatherproof enclosure. Shutdown switch is a momentary pushbutton type with a clear, hinged spring-loaded cover to minimize tampering.
Fueling System Emergency Shut-Down E-Stop Switch With High Visibility Yellow Surface-Mount Guarded Weatherproof Enclosure
Item No. EM01G
Fueling system emergency shutdown switch mounted in a guarded enclosure with a high visibility yellow cover. Shutdown switch is a momentary pushbutton type protected from the weather and accidental contact by the semi-circle guard.
50ml Cartridge 10:1 Mix Ratio PolyFuse Structural Bonder For HDPE Sumps, With Nitrile Gloves And Squeegee
Item No. IAC PFUSE50
Icon PolyFuse is a 2-part acrylic-based structural bonder used for the repair of minor damage in petroleum containment sumps made of low energy plastics such as high-density polyethylene (HDPE). Also works in combination with other materials like fiberglass. With proper surface preparation and product application, the repair can be a permanent solution to a sump leak issue, eliminating the need for immediate and expensive sump replacement. Fuel Compatibility PolyFuse is compatible with all fuel types and blends.
Low-Voltage Dispenser Data And Card Reader Disconnect With CAT5/6 For Up To (4) Dispensers With Video Capabilities
Item No. LVDD-V-4
The Square D IPaCS LVDD Low Voltage Dispenser Disconnect provides a means to disconnect low voltage electrical circuits such as audio, video, data and communication circuits leading to or through dispensing equipment. The LVDD is intended to be used at fueling sites to provide compliance with National Fire Protection Association (NFPA) 30A Section 6.7 and National Electric Code (NEC) Sections 514.11 and 514.13. Features Integrated single point of disconnect capability for Power and Low Voltage circuits when installed with DMEX Dispenser Manager Solutions. Compatible with any fueling control system and all dispenser manufacturers Suitable for both New and Retrofit Construction Modular design saves valuable wall space Individual dispenser disconnects and switches are wired into the emergency shutdown system and isolate lower voltages for maintenance and servicing purposes
FRP Series Full Ring Pass-Thru FRP Entry Fitting For 1 Inch Galvanized Conduit On Flat-Wall Sump *EP2A Or ADH-300G Adhesive Required*
Item No. PF-FRP-1F-C1
The Full Ring Pass-Thru FRP New Construction Entry Fitting has a small profile and occupies little space in a crowded sump. Features 100% fiberglass construction provides superior strength and ensures the fitting will withstand long-term exposure to all fuels, including ethanol Small profile saves space in sump. Works with angled pipe entries up to 10° for job site adaptability allowing room for misalignment Cost-effective affordable fiberglass fitting with a similar cost to rubber or plastic fittings
FRP Series Full Ring Pass-Thru FRP Entry Fitting For 3/4 Inch Galvanized Conduit On Flat-Wall Sump *EP2A Or ADH-300G Adhesive Required*
Item No. PF-FRP-1F-C8
The Full Ring Pass-Thru FRP New Construction Entry Fitting has a small profile and occupies little space in a crowded sump. Features 100% fiberglass construction provides superior strength and ensures the fitting will withstand long-term exposure to all fuels, including ethanol Small profile saves space in sump. Works with angled pipe entries up to 10° for job site adaptability allowing room for misalignment Cost-effective affordable fiberglass fitting with a similar cost to rubber or plastic fittings
FRP Series Full Ring Pass-Thru FRP Entry Fitting For 1 Inch PVC Coated Conduit On Flat-Wall Sump *EP2A Or ADH-300G Adhesive Required*
Item No. PF-FRP-1F-K1
The Full Ring Pass-Thru FRP New Construction Entry Fitting has a small profile and occupies little space in a crowded sump. Features 100% fiberglass construction provides superior strength and ensures the fitting will withstand long-term exposure to all fuels, including ethanol Small profile saves space in sump. Works with angled pipe entries up to 10° for job site adaptability allowing room for misalignment Cost-effective affordable fiberglass fitting with a similar cost to rubber or plastic fittings
FRP Series Full Ring Pass-Thru FRP Entry Fitting For 3/4 Inch PVC Coated Conduit On Flat-Wall Sump *EP2A Or ADH-300G Adhesive Required*
Item No. PF-FRP-1F-K8
The Full Ring Pass-Thru FRP New Construction Entry Fitting has a small profile and occupies little space in a crowded sump. Features 100% fiberglass construction provides superior strength and ensures the fitting will withstand long-term exposure to all fuels, including ethanol Small profile saves space in sump. Works with angled pipe entries up to 10° for job site adaptability allowing room for misalignment Cost-effective affordable fiberglass fitting with a similar cost to rubber or plastic fittings
FRP Series Full Ring Pass-Thru FRP Entry Fitting For 2 Inch LCX Pipe On Flat-Wall Sump *EP2A Or ADH-300G Adhesive Required*
Item No. PF-FRP-1F-L2
The Full Ring Pass-Thru FRP New Construction Entry Fitting has a small profile and occupies little space in a crowded sump. Features 100% fiberglass construction provides superior strength and ensures the fitting will withstand long-term exposure to all fuels, including ethanol Small profile saves space in sump. Works with angled pipe entries up to 10° for job site adaptability allowing room for misalignment Cost-effective affordable fiberglass fitting with a similar cost to rubber or plastic fittings
FRP Series Full Ring Pass-Thru FRP Entry Fitting For 3 Inch LCX Pipe On Flat-Wall Sump *EP2A Or ADH-300G Adhesive Required*
Item No. PF-FRP-1F-L3
The Full Ring Pass-Thru FRP New Construction Entry Fitting has a small profile and occupies little space in a crowded sump. Features 100% fiberglass construction provides superior strength and ensures the fitting will withstand long-term exposure to all fuels, including ethanol Small profile saves space in sump. Works with angled pipe entries up to 10° for job site adaptability allowing room for misalignment Cost-effective affordable fiberglass fitting with a similar cost to rubber or plastic fittings
FRP Series Full Ring Pass-Thru FRP Entry Fitting For 4 Inch LCX Pipe On Flat-Wall Sump *EP2A Or ADH-300G Adhesive Required*
Item No. PF-FRP-1F-L4
The Full Ring Pass-Thru FRP New Construction Entry Fitting has a small profile and occupies little space in a crowded sump. Features 100% fiberglass construction provides superior strength and ensures the fitting will withstand long-term exposure to all fuels, including ethanol Small profile saves space in sump. Works with angled pipe entries up to 10° for job site adaptability allowing room for misalignment Cost-effective affordable fiberglass fitting with a similar cost to rubber or plastic fittings
FRP Series Full Ring Pass-Thru FRP Entry Fitting For 2 Inch RTII Pipe On Flat-Wall Sump *EP2A Or ADH-300G Adhesive Required*
Item No. PF-FRP-1F-R2
The Full Ring Pass-Thru FRP New Construction Entry Fitting has a small profile and occupies little space in a crowded sump. Features 100% fiberglass construction provides superior strength and ensures the fitting will withstand long-term exposure to all fuels, including ethanol Small profile saves space in sump. Works with angled pipe entries up to 10° for job site adaptability allowing room for misalignment Cost-effective affordable fiberglass fitting with a similar cost to rubber or plastic fittings
FRP Series Full Ring Pass-Thru FRP Entry Fitting For 3 Inch RTII Pipe On Flat-Wall Sump *EP2A Or ADH-300G Adhesive Required*
Item No. PF-FRP-1F-R3
The Full Ring Pass-Thru FRP New Construction Entry Fitting has a small profile and occupies little space in a crowded sump. Features 100% fiberglass construction provides superior strength and ensures the fitting will withstand long-term exposure to all fuels, including ethanol Small profile saves space in sump. Works with angled pipe entries up to 10° for job site adaptability allowing room for misalignment Cost-effective affordable fiberglass fitting with a similar cost to rubber or plastic fittings
SRB Series Split Repair FRP Entry Fitting With Stainless Band Clamp For 1 Inch Galvanized Conduit On Flat-Wall Sump *EP2A Or ADH-300G Adhesive Required*
Item No. PF-SRB-1F-C1
The Split Repair FRP Entry Fitting With Band Clamp makes repairs straight forward and allows for field modification. Features Stainless Band Clamp holds fitting in place and the Retention Rim prevents the clamp from sliding off the fitting while the epoxy cures Can be modified in the field to simplify service work 100% fiberglass construction provides superior strength and ensures the fitting will withstand long-term exposure to all fuels, including ethanol Works with angled pipe entries up to 10° for job site adaptability allowing room for misalignment Cost-effective affordable fiberglass fitting with a similar cost to rubber or plastic fittings
SRB Series Split Repair FRP Entry Fitting With Stainless Band Clamp For 3/4 Inch Galvanized Conduit On Flat-Wall Sump *EP2A Or ADH-300G Adhesive Required*
Item No. PF-SRB-1F-C8
The Split Repair FRP Entry Fitting With Band Clamp makes repairs straight forward and allows for field modification. Features Stainless Band Clamp holds fitting in place and the Retention Rim prevents the clamp from sliding off the fitting while the epoxy cures Can be modified in the field to simplify service work 100% fiberglass construction provides superior strength and ensures the fitting will withstand long-term exposure to all fuels, including ethanol Works with angled pipe entries up to 10° for job site adaptability allowing room for misalignment Cost-effective affordable fiberglass fitting with a similar cost to rubber or plastic fittings
SRB Series Split Repair FRP Entry Fitting With Stainless Band Clamp For 2 Inch LCX Pipe On Flat-Wall Sump *EP2A Or ADH-300G Adhesive Required*
Item No. PF-SRB-1F-L2
The Split Repair FRP Entry Fitting With Band Clamp makes repairs straight forward and allows for field modification. Features Stainless Band Clamp holds fitting in place and the Retention Rim prevents the clamp from sliding off the fitting while the epoxy cures Can be modified in the field to simplify service work 100% fiberglass construction provides superior strength and ensures the fitting will withstand long-term exposure to all fuels, including ethanol Works with angled pipe entries up to 10° for job site adaptability allowing room for misalignment Cost-effective affordable fiberglass fitting with a similar cost to rubber or plastic fittings
SRB Series Split Repair FRP Fiberglass Entry Fitting With Stainless Band Clamp For 3 Inch LCX Pipe On Flat Wall Sump *EP2A Or ADH-300G Adhesive Required*
Item No. PF-SRB-1F-L3
The Split Repair FRP Entry Fitting With Band Clamp makes repairs straight forward and allows for field modification. Features Stainless Band Clamp holds fitting in place and the Retention Rim prevents the clamp from sliding off the fitting while the epoxy cures Can be modified in the field to simplify service work 100% fiberglass construction provides superior strength and ensures the fitting will withstand long-term exposure to all fuels, including ethanol Works with angled pipe entries up to 10° for job site adaptability allowing room for misalignment Cost-effective affordable fiberglass fitting with a similar cost to rubber or plastic fittings
SRB Series Split Repair FRP Entry Fitting With Stainless Band Clamp For 3/4 Inch Galvanized Conduit On Round-Wall Sump *EP2A Or ADH-300G Adhesive Required*
Item No. PF-SRB-1R-C8
The Split Repair FRP Entry Fitting With Band Clamp makes repairs straight forward and allows for field modification. Features Stainless Band Clamp holds fitting in place and the Retention Rim prevents the clamp from sliding off the fitting while the epoxy cures Can be modified in the field to simplify service work 100% fiberglass construction provides superior strength and ensures the fitting will withstand long-term exposure to all fuels, including ethanol Works with angled pipe entries up to 10° for job site adaptability allowing room for misalignment Cost-effective affordable fiberglass fitting with a similar cost to rubber or plastic fittings
SRB Series Oversize Split Repair FRP Entry Fitting With Stainless Band Clamp For 3/4 Inch Galvanized Conduit On Flat Wall Sump *EP2A Or ADH-300G Adhesive Required*
Item No. PF-SRB-2F-C8
The Oversized Split Repair FRP Entry Fitting With Band Clamp makes repairs straight forward and allows for field modification. Oversized model eliminates need to pair the SRB with a BSO fitting. Features Stainless Band Clamp holds fitting in place and the Retention Rim prevents the clamp from sliding off the fitting while the epoxy cures Can be modified in the field to simplify service work 100% fiberglass construction provides superior strength and ensures the fitting will withstand long-term exposure to all fuels, including ethanol Works with angled pipe entries up to 10° for job site adaptability allowing room for misalignment Cost-effective affordable fiberglass fitting with a similar cost to rubber or plastic fittings