2 Inch Slip On
1-1/2 Inch Union
Narrow Your Results
Mfr / Trade Name
Category - Main
Containment Sumps, Monitoring Wells & Flex Connectors
Valves, Drop Tubes & Vents
Fiberglass
Flexible Piping
Semi-Rigid
Test & Temination Reducers
Accessory
Type
Composition
Size
Length
Inlet
- List View
- Gallery View
| Page of 1 |
3 Inch X 2 Inch Reducer Bushing Scarfed O.D. X Taper I.D.
Item No. 012030-231-7
UL 971 listed
3-1/2 Inch Id X 30 Inch Long Flex Containment Boot
Item No. 1001
Clamped directly to 3 inch secondary pipe used over 2 inch primary pipe
1-1/2 Inch NPT Union-Top 10 Series Single-Poppet Emergency Shut-Off Shear Valve
Item No. 10BU-5925
Installed on fuel supply lines beneath dispenser at grade level
1-1/2 Inch NPT Union-Top 10 Series Double Poppet Emergency Shut-Off Shear Valve
Item No. 10BUP-5926
Installed on fuel supply lines beneath dispenser at grade level
3 Inch X 2 Inch Primary Reducer Bushing
Item No. 32370504
Proven reliable fiberglass pipe system
3 Inch X 2 Inch Secondary Containment Reducer With 3/4 Inch Test Port (2 Piece)
Item No. 32387604
Proven reliable fiberglass pipe system
3 Inch X 2 Inch Containment Reducer Ring (3 Piece Combo)
Item No. 32469208
Installs in one half the time of conventional fiberglass pipe
2 Inch Diffuser - Slip-On Aluminum
Item No. 539AS-0200AD
Designed for installation at the bottom end of a drop tube to reduce turbulence and vapor loss during the filling operation
2 Inch Upward V Vent Polyethylene
Item No. A4103-002
Slip-on style attaches to 1.5 inch-2.0 inch pipe with 3 set screws
25 Inch Wide x 24 Inch Deep x 31 Inch Tall FlexWorks 1-Piece Polyethylene UDC Under Dispenser Containment Sump With 11 Inch x 23 Inch Frame For Gasboy Dispensers
Item No. DS-1123
The DS-1123 Polyethylene Dispenser Sump is designed to be used with these dispensers Gasboy 28-1/4 inch frame 8700, 8800, 9100, and 9800 Series with 17-1/4 inch x 28 inch footprint.
25 Inch Wide x 24 Inch Deep x 31 Inch Tall FlexWorks 1-Piece Polyethylene UDC Under Dispenser Containment Sump With 11 Inch x 23 Inch Flush-Mount Frame For Gilbarco And Wayne Dispensers
Item No. DS-1123F
The DS-1123F Polyethylene Dispenser Sump is designed to be used with these dispensers Gilbarco 27 inch frame Highline 11B Series with 15-11/16 inch x 21 inch footprint. Gilbarco 27 inch frame Trimline 251, 252, 261, 262 Series with 15-11/16 inch x 27 inch footprint. Gilbarco 27 inch frame Commercial 650 Series with 15-11/16 inch x 27 inch footprint. Gilbarco 27 inch frame Highline Salesmaker Series with 15-11/16 inch x 27 inch footprint. Gilbarco 27 inch frame Salesmaker-4 Series with 15-11/16 inch x 27 inch footprint. Gilbarco Legacy Series with 15-11/16 inch x 27 inch footprint. Dresser Wayne 350, 357, 358, 360, 370 Series with 15 inch x 25-7/8 inch footprint.
Fiberglass Dispenser Sump 11 Inch X 23 Inch
Item No. DSF-1123
Engineered with thick side walls to withstand backfill and high water table forces
3 Inch To 2 Inch FRP Rubber Test Boot With Air Stem/Test Port
Item No. TBA-3020
Used to isolate and air test the interstitial space between the primary and secondary pipe
3 Inch x 2 Inch UPP Primary Singlewall Reducer Fitting UL-971 Listed
Item No. 09-090-063EIF-U
2 Inch Pressure Vacuum Vent Slip On 8 Ounce Pressure 1/2 Ounce Vacuum
Item No. 523V-1150
Factory preset and tested settings
2 Inch Pressure Vacuum Vent Slip On 3 Inch Water Column Pressure 8 Inch Water Column Vacuum
Item No. 523V-2253
Factory preset and tested settings
3 Inch x 2 Inch Test Reducer With Stainless Steel Air Test Valve
Item No. PF-RA 3.6X2.4 ASS
F Series Full-Body Taper-By-Slip Pass-Through FRP Entry Fitting With Dual Test Ports And Single Injection Port For 3 x 2 Inch FRP Pipe On Flat-Wall Single Or Doublewall Sump - (2) EP100 Required
Item No. F-32S-T-F
Bonded FRP new construction full-body termination entry fitting for singlewall or doublewall sumps.
